It’s solid, rugged, and nice to look at!BÜRP is a high quality extruded aluminium enclosure that holds your favourite RISC OS (or Linux if you prefer) board, such as the Raspberry Pi, Wandboard Quad (ARMx6), IGEPv5 or Beagleboard. A Pandaboard ES can fit, but only if the serial port is safely de-soldered and removed. With enough room inside for the board itself - and in the case of the ARMx6 and IGEPv5, the hard disc too - the BURP enables all cables and connections to come out in the same direction, tidying the desk area.In addition, being made of hardwearing aluminium, BÜRP is portable and can withstand some of the bumps and knocks that would damage other cases.BÜRP comes in two sizes. The standard size has a length of 160mm from end to end, while the extended version is 220mm. The Raspberry Pi, Beagleboard and ARMx6 fit nicely in the standard size, whilst we recommend the extended version for the IGEPv5 and the Wandboard Quad (ARMx6) with internal USB hub, just to make the cables fit more comfortably.Not everyone wants the same colour case for each board they own, so BÜRP has four colours to choose from. You may wish to put your Raspberry Pi in a Rapberry red case, your ARMx6 in an electric blue case, your IGEPv5 in a silver case and your Beagleboard in a black case. Obviously you can choose your own colour to fit your own needs, but at least you can make each board easily identifiable.Please note that cables are not supplied as the requirements for each board are different. We include a list of appropriate cables with each board so that you can purchase the cables suitable for your board. However, if you tell us which board you intend to use, we can supply a suitable cable pack at additional cost.
BÜRP Extended220mm in lengthCompete with end plate allowing for:1x RJ451x HDMI3x USB 2.01x 3.5mm audio1x 2.1mm DC connector (installed)4x push in holders for the end plate8x machine screws for more permanent fixing4x rubber feetIncludes a single internal mounting plate for attaching your board and peripherals, which can be easily cut to size with a sharp knife and drilled as appropriate to your board and your chosen layout.£52.50 plus £4.50 p&p
BÜRP Standard160mm in lengthCompete with end plate allowing for:1x RJ451x HDMI3x USB 2.01x 3.5mm audio1x 2.1mm DC connector (installed)4x push in holders for the end plate8x machine screws for more permanent fixing4x rubber feetIncludes a single internal mounting plate for attaching your board and peripherals, which can be easily cut to size with a sharp knife and drilled as appropriate to your board and your chosen layout.£44.50 plus £4.50 p&p
For those who don’t like dabbling with the internals of their computers, take advantage of the RÜGGEDISER service. Simply get in touch to make arrangements to send your current working machine, and we can transplant the insides of your existing machine and remount them inside aBÜRP case, wherever possible.
We can also build you a bespoke BÜRP machine, such as a RISC OS Rapsberry Pi with SATA SSD storage, like the ROKit. Within reason, we can
build your BÜRP machine to your specifications, subject to limitations of available hardware and software, and the constraints of the extruded
BÜRP Flight CaseObviously the BÜRP is rugged and hardwearing, but you may want to carry it around with you, along with a few accessories.With enough room for a single BÜRP Standard or BÜRP Extended along with a PSU and a mouse, the BÜRP Flight Case makes carrying your development board around so much easier. It can even hold two BÜRP Standards at the same time, but you’ll have to put the PSU in your pocket.The flight case is made of rugged aluminium on the outside, with soft foam lining and a foam insert on the inside. Just cut the foam insert to suit your BÜRP and the accessories you want to carry around, and you’re away Perfect for those who want to BÜRP in lots of different places!only £19.50 inc p&pwhen purchased with a BÜRP